What’s in the box (DD24)
Contents
What’s in the box (DD24)#
What should you expect to find inside a Duckiedrone (DD24) box, and what is each component?
First things first: here is how a Duckiedrone box looks like:
Fig. 6 The yellow Duckiedrone box.#
And is here an incomplete representation of the components in the box. Continue scrolling for the complete list.
Fig. 7 What’s inside the box (selected components).#
List of components#
Component |
Number |
|---|---|
1 |
Raspberry Pi 4 - 4GB (or Raspberry Pi 5) |
1 |
64GB MicroSD card - Class 10 U3 |
1 |
MicroSD to USB adapter |
1 |
RPi Camera (G) - Fisheye lens |
1 |
Camera cable - 300mm |
5 |
ToF sensor - VL53L1X, Black PCB |
4 |
ToF sensor cable - 15cm, 4-pin JST 1.5mm |
1 |
ToF sensor cable - 23cm, 4-pin JST 1.5mm |
2 |
Motors (CW) - LHI DX2205 2300KV |
2 |
Motors (CCW) - LHI DX2205 2300KV |
4 |
Propellers (CW) - Diatone Polycarbonate 4040 |
4 |
Propellers (CCW) - Diatone Polycarbonate 4040 |
1 |
LiPo Battery - 1500mAh, 4S, 14.8V, 76x35x33mm, XT60 connector, 10cm cable, 35C peak discharge |
1 |
Battery charger - 2-4S Li-Ion/Li-Poly, 25W |
1 |
Battery charger adapter - 12V 2A US plug |
1 |
Duckietown drone HUT - v1.1 |
1 |
Breadboard - Yellow, 45x35mm |
1 |
Flight Controller & ESC stack - SpeedyBee F405 V3, BLS 50A |
1 |
Buzzer - Model 2312, 3V-24V |
1 |
USB-A to USB-C cable - 23cm, angled |
1 |
USB-C power cable - 10cm, exposed wires |
2 |
Header jumpers - 2.54mm spacing, black |
1 |
Heat sink kit - Multiple sizes |
1 |
40mm GPIO Fan - PWM speed control, 3-pin |
2 |
Velcro strips - 10inch, black |
1 |
Bottom Plate - Carbon fiber, 2.5mm thick |
1 |
Top Plate - Carbon fiber, 2.5mm thick |
2 |
ToF support - Carbon fiber, 2.5mm thick |
2 |
Fan duct wall - Carbon fiber, 2.5mm thick |
1 |
Battery support - Carbon fiber, 2.5mm thick |
1 |
Camera + ToF mount - ABS material |
4 |
Landing Gear - 3D printed v1.1 |
8 |
Rubber Pads |
18 |
Metal screws (M3x14) - Steel, Phillips head |
13 |
Nylon screws (M2.5x8) - For Pi Hat, ToF sensors |
3 |
Nylon Standoff (M2.5x40+6 MF) - Battery Plate to Pi |
5 |
Nylon Standoff (M2.5x20+6 MF) - Raspberry Pi mounting |
5 |
Nylon Standoff (M2.5x15+6 FF) - Pi to Pi Hat |
6 |
Nylon Nuts (M2.5) - ToF sensors |
4 |
Nylon screws (M3x10) - Camera mount |
7 |
Nylon screws (M2x10) - Camera, Buzzer |
7 |
Nylon Nuts (M2) - Camera, Buzzer |
24 |
Nylon screws (M3x6) - Chassis, battery supports |
10 |
Nylon Standoff (M3x35+6 FF) - Chassis |
3 |
Nylon Standoff (M3x40+6 FF) - Battery supports |
3 |
Nylon Standoff (M3x6+6 MF) - Fan mounting |
6 |
Nylon Nuts (M3) - Battery, camera mount |
12 |
Nylon Standoff (M3 35+6 MF) - Chassis |
5 |
Metal screws (M3x20) - Flight Controller |
1 |
8mm wrench - Motor compatibility check |
1 |
Screwdriver - Cross |
1 |
Camera Calibration pattern |
2 |
Rubber Duckies - Duckietown swag |
2 |
Duckietown Stickers - Duckietown swag |
1 |
Instruction card - Drone assembly |
1 |
Internal Packaging Skin |
1 |
Duckiedrone box |
1 |
Shipping Package box |
In the following section Description of Components (DD24) we provide a brief description of each component.